Maxtor 86480D8 Specifications Page 29
- Page / 62
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
INSTALLATION
4 – 29
c) If the system has an older BIOS which does not provide a UDT, set the BIOS for the Maxtor hard
drive to Type 9. If this BIOS setting is used or the BIOS does not support LBA, the drive must be
prepared using Max•Blast software.
3. After the drive parameters are entered, follow the SETUP program procedures to save the settings and exit
the SETUP program. After changing BIOS settings, saving the values and exiting, the SETUP program should
force the system to re-boot.
Boot the system to the bootable Max•Blast installation software diskette received with the hard drive or with a
DOS 5.0 (or higher) or Windows 95 system diskette. If the system boots normally, proceed to the “Hard Drive
Preparation” section.
System Hangs During Boot
If after installing the Maxtor hard drive in the system or after setting the system BIOS the system hangs during the
boot process, the system may have a BIOS limitation. This may occur for drives with capacities larger than 2.1 GB.
If the system locks up before accessing the BIOS SETUP program or if it locks up during the boot process after
setting the system BIOS, the system may have a BIOS with a cylinder limitation. If this happens, perform the
following:
1 Turn the system OFF.
2 Install jumper J46 on the drive using the spare jumper shipped across pins J46 and J48 or if the drive is installed as
a Slave, store the spare jumper across J42 and J44.
3 If the BIOS was set to AUTO DETECT, re-boot the system and use Max•Blast installation software to
complete the hard drive installation. If other BIOS settings were used, access the system BIOS SETUP program
and set the BIOS parameters to Type 9 for the Maxtor hard drive then re-boot the system and use Max•Blast
installation software to complete the hard drive installation. NOTE: When this jumper is installed, the Maxtor
hard drive must be prepared using Max•Blast.
- DiamondMax™ 1750 UDMA 1
- Revisions Manual No. 1381 2
- Before You Begin 3
- Contents 4
- Glossary 6
- Figure Title Page 7
- SECTION 1 8
- Introduction 8
- Conventions 9
- SECTION 2 10
- Product Description 10
- Product Features 11
- Logical Block Addressing 12
- Defect Management Zone (DMZ) 12
- Software ECC Correction 12
- Cache Management 13
- Major HDA Components 14
- 4092 Cylinder Limitation 15
- Subsystem Configuration 15
- Jumper Location/Configuration 15
- SECTION 3 16
- Product Specifications 16
- Physical Dimensions 17
- Power Requirements (Average) 18
- Power Mode Definitions 18
- Environmental 18
- Reliability and Maintenance 19
- Data Reliability 19
- Acoustic Noise 19
- EPA Energy Star Compliance 19
- Shock and Vibration 19
- Standard Test Methods 20
- Safety Regulatory Compliance 20
- SECTION 4 21
- Handling and Installation 21
- Unpacking and Inspection 22
- Repacking 23
- Physical Installation 23
- Drive Jumper Settings 24
- Mounting Drive in System 24
- Figure 4 - 6 25
- 5.25-inch Installation 25
- Figure 4 - 7 25
- 3.5-inch Installation 25
- Figure 4 - 8 26
- Attaching System Cables 27
- System Setup 28
- System Hangs During Boot 29
- Hard Drive Preparation 30
- SECTION 5 31
- AT Interface Description 31
- Pin Description Table 32
- PIO Timing 33
- DMA Timing 34
- Ultra DMA Timing 35
- Figure 5 - 5 36
- Figure 5 - 6 36
- Figure 5 - 7 37
- Figure 5 - 8 37
- Figure 5 - 9 38
- Figure 5 - 10 38
- Figure 5 - 11 39
- Figure 5 - 12 39
- Figure 5 - 13 40
- SECTION 6 41
- Host Software Interface 41
- Sector Count Register 42
- Sector Number Register 42
- Cylinder Number Registers 42
- Device/Head Register 42
- Status Register 42
- Command Register 43
- HOST SOFTWARE INTERFACE 44
- Control Diagnostic Registers 45
- Reset and Interrupt Handling 46
- SECTION 7 47
- Interface Commands 47
- Read Commands 48
- Read DMA 49
- Read Multiple 49
- Set Multiple Mode 49
- Write Commands 50
- Write Multiple 51
- Write DMA 51
- Set Feature Commands 52
- Power Mode Commands 53
- INTERFACE COMMANDS 54
- Initialization Commands 55
- Initialize Drive Parameters 58
- ERROR CODE DESCRIPTION 59
- 01 No error detected 59
- 00 Master drive failed 59
- 81 Slave drive failed 59
- S.M.A.R.T. Command Set 60
- SECTION 8 61
- Service and Support 61
- Service 62
- Internet 62
- Bulletin Board Service 62
- Customer Service 62
Related products and manuals for Internal hard drives Maxtor 86480D8
(50 pages)© 2020, manymanuals.com. All rights reserved. | 1.153 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals