Maxtor 86480D8 Specifications Page 28
- Page / 62
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
INSTALLATION
4 – 28
System Setup
The following procedures are designed for systems using the DOS 5.0 (or higher) or Windows 95 operating systems.
For other operating systems (e.g., OS2
®
, UNIX
®
, LINUX and Novell NetWare
®
), refer to the operating system
user’s manual for the BIOS setting and other installation requirements
Setting the BIOS (CMOS)
In order for the computer system to recognize the new Maxtor hard drive, it is necessary to set the system BIOS
with the correct information about the hard drive.
The SETUP (BIOS) program identifies the system configuration information (e.g., floppy disk drives, hard disk
drives, video, etc.) used by the computer during system boot. This includes the information about what kind and
how many hard drives are attached to the system. When entering the settings for the new Maxtor hard drive, be
careful not to change any of the other BIOS settings, or other parts of the system may not work correctly.
Most of the systems with newer BIOS’ (typically with a date of July 1994 or newer), support large capacity hard
drives. It is necessary to determine if the system provides support for large capacity hard drives before entering the
settings, as this affects how to correctly set the BIOS parameters for the new Maxtor hard drive.
If you are unsure of how to access the system BIOS and/or program the BIOS settings, refer to the computers user’s
manual for detailed instructions.
Set the BIOS (CMOS) parameters as follows:
1. Turn the system ON. During the system start-up sequence, run the SETUP (BIOS) program or similar
commands to access the system BIOS.
NOTE: Newer systems will typically display a message (e.g., press DEL to Enter Setup) identifying how to
access the SETUP (BIOS) program.
2. Once the SETUP (BIOS) program is active, do one of the following to set the hard drive BIOS parameters.
a) If the SETUP program provides an “AUTO DETECT” capability, use this feature to detect the
Maxtor hard drive. After the SETUP program has detected the hard drive, verify that the Logical
Block Addressing (LBA) mode is enabled for this drive. If the SETUP program does not provide
an “AUTO DETECT” capability, set the drive parameters as defined in b) below.
Comment: When LBA is enabled, some BIOS programs will change the values of the cylinders
and heads by dividing the cylinders by 2, 4, 8 or 16 and multiplying the heads by the same value.
This does not change the capacity of the hard drive.
b) If the SETUP program does not provide an “AUTO DETECT” capability, the drive parameters
must be set using the User Definable Type (UDT). Select the appropriate UDT for the Maxtor hard
drive and set the cylinder, head and sector values for the model being installed from the table below.
Only the values listed in the table must be entered. Other values may be entered as zero (0). Set the
LBA mode to enabled for this drive. If the SETUP program does not provide the UDT, set the drive
parameters as defined in c) below.
Drive Parameters
MO D E L CYLI NDERS HEADS SECTORS CAPACI TY
87000D8 14,475 15 63 7,000 MB
86480D8 13,392 15 63 6,480 MB
85250D6 10,856 15 63 5,250 MB
84320D5 8,928 15 63 4,320 MB
83500D4 7,237 15 63 3,500 MB
83240D4 6,696 15 63 3,240 MB
82560D3 5,292 15 63 2,560 MB
81750D2 3,618 15 63 1,750 MB
- DiamondMax™ 1750 UDMA 1
- Revisions Manual No. 1381 2
- Before You Begin 3
- Contents 4
- Glossary 6
- Figure Title Page 7
- SECTION 1 8
- Introduction 8
- Conventions 9
- SECTION 2 10
- Product Description 10
- Product Features 11
- Logical Block Addressing 12
- Defect Management Zone (DMZ) 12
- Software ECC Correction 12
- Cache Management 13
- Major HDA Components 14
- 4092 Cylinder Limitation 15
- Subsystem Configuration 15
- Jumper Location/Configuration 15
- SECTION 3 16
- Product Specifications 16
- Physical Dimensions 17
- Power Requirements (Average) 18
- Power Mode Definitions 18
- Environmental 18
- Reliability and Maintenance 19
- Data Reliability 19
- Acoustic Noise 19
- EPA Energy Star Compliance 19
- Shock and Vibration 19
- Standard Test Methods 20
- Safety Regulatory Compliance 20
- SECTION 4 21
- Handling and Installation 21
- Unpacking and Inspection 22
- Repacking 23
- Physical Installation 23
- Drive Jumper Settings 24
- Mounting Drive in System 24
- Figure 4 - 6 25
- 5.25-inch Installation 25
- Figure 4 - 7 25
- 3.5-inch Installation 25
- Figure 4 - 8 26
- Attaching System Cables 27
- System Setup 28
- System Hangs During Boot 29
- Hard Drive Preparation 30
- SECTION 5 31
- AT Interface Description 31
- Pin Description Table 32
- PIO Timing 33
- DMA Timing 34
- Ultra DMA Timing 35
- Figure 5 - 5 36
- Figure 5 - 6 36
- Figure 5 - 7 37
- Figure 5 - 8 37
- Figure 5 - 9 38
- Figure 5 - 10 38
- Figure 5 - 11 39
- Figure 5 - 12 39
- Figure 5 - 13 40
- SECTION 6 41
- Host Software Interface 41
- Sector Count Register 42
- Sector Number Register 42
- Cylinder Number Registers 42
- Device/Head Register 42
- Status Register 42
- Command Register 43
- HOST SOFTWARE INTERFACE 44
- Control Diagnostic Registers 45
- Reset and Interrupt Handling 46
- SECTION 7 47
- Interface Commands 47
- Read Commands 48
- Read DMA 49
- Read Multiple 49
- Set Multiple Mode 49
- Write Commands 50
- Write Multiple 51
- Write DMA 51
- Set Feature Commands 52
- Power Mode Commands 53
- INTERFACE COMMANDS 54
- Initialization Commands 55
- Initialize Drive Parameters 58
- ERROR CODE DESCRIPTION 59
- 01 No error detected 59
- 00 Master drive failed 59
- 81 Slave drive failed 59
- S.M.A.R.T. Command Set 60
- SECTION 8 61
- Service and Support 61
- Service 62
- Internet 62
- Bulletin Board Service 62
- Customer Service 62
Related products and manuals for Internal hard drives Maxtor 86480D8
(50 pages)© 2020, manymanuals.com. All rights reserved. | 4.908 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals