Maxtor 86480D8 Specifications Page 21
- Page / 62
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
INSTALLATION
4 – 21
SECTION 4
Handling and Installation
Pre-formatted Drive
This Maxtor hard drive has been low-level formatted at the factory. Do not use a low-level formatting program.
Important Notice
There are a number of system BIOS’s currently in use which do not support hard drives with more than 4095
cylinders (2.1 gigabytes). This section contains information describing the conditions which may identify this
limitation. In order to obtain the full capacity of your Maxtor drive, you will need to follow the suggested
installation instructions.
Hard Drive Handling Precautions
Please take a moment to observe the following handling cautions:
❏ During handling,
NEVER
drop, jar, or bump a drive. Handle the drive by its sides and avoid touching the printed circuit
board assembly (PCBA).
❏ Hard drives are sensitive to electrostatic discharge (ESD) damage. Use proper ESD practices by grounding yourself and
the computer system the hard drive will be installed in.
❏ Allow the hard drive to reach room temperature
BEFORE
installing it in your computer system.
❏
NEVER
switch DC power onto the drive by plugging an electrically live DC source cable into the drive's connector.
NEVER
connect a live connector to the hard drive's IDE interface connector.
Electro-Static Discharge (ESD)
To avoid some of the problems associated with ESD, Maxtor advises that anyone handling a disk drive use a wrist
strap with an attached wire connected to an earth ground. Failure to observe these precautions voids the warranty.
Manufacturers frequently experience “unsolved” component/hardware malfunctions often caused by ESD. To
reduce the incidence of ESD-related problems, Maxtor recommends that any electronics manufacturing plans
include a comprehensive ESD program, the basic elements and functions of which are outlined here:
ESD Program Element ESD Program Function
Management Institute and maintain
Chief coordinator Organize and enforce
Multi-department committee Evaluate and improve
Employee training Educate and inform
ESD program supplies typically include: wrist- and foot-worn grounding straps; counter-top and floor antistatic
matting; wrist strap testers; ESD video and training materials. Sources for such supplies include:
Static Control Systems – 3M Charleswater
225-4S, 3M Center 93 Border St.
St. Paul, MN 55144 West Newton, MA 02165-9990
Maxtor also offers a complete video training package, “Care and Handling of Maxtor Disk Drives.”
Contact your Maxtor representative for details.
- DiamondMax™ 1750 UDMA 1
- Revisions Manual No. 1381 2
- Before You Begin 3
- Contents 4
- Glossary 6
- Figure Title Page 7
- SECTION 1 8
- Introduction 8
- Conventions 9
- SECTION 2 10
- Product Description 10
- Product Features 11
- Logical Block Addressing 12
- Defect Management Zone (DMZ) 12
- Software ECC Correction 12
- Cache Management 13
- Major HDA Components 14
- 4092 Cylinder Limitation 15
- Subsystem Configuration 15
- Jumper Location/Configuration 15
- SECTION 3 16
- Product Specifications 16
- Physical Dimensions 17
- Power Requirements (Average) 18
- Power Mode Definitions 18
- Environmental 18
- Reliability and Maintenance 19
- Data Reliability 19
- Acoustic Noise 19
- EPA Energy Star Compliance 19
- Shock and Vibration 19
- Standard Test Methods 20
- Safety Regulatory Compliance 20
- SECTION 4 21
- Handling and Installation 21
- Unpacking and Inspection 22
- Repacking 23
- Physical Installation 23
- Drive Jumper Settings 24
- Mounting Drive in System 24
- Figure 4 - 6 25
- 5.25-inch Installation 25
- Figure 4 - 7 25
- 3.5-inch Installation 25
- Figure 4 - 8 26
- Attaching System Cables 27
- System Setup 28
- System Hangs During Boot 29
- Hard Drive Preparation 30
- SECTION 5 31
- AT Interface Description 31
- Pin Description Table 32
- PIO Timing 33
- DMA Timing 34
- Ultra DMA Timing 35
- Figure 5 - 5 36
- Figure 5 - 6 36
- Figure 5 - 7 37
- Figure 5 - 8 37
- Figure 5 - 9 38
- Figure 5 - 10 38
- Figure 5 - 11 39
- Figure 5 - 12 39
- Figure 5 - 13 40
- SECTION 6 41
- Host Software Interface 41
- Sector Count Register 42
- Sector Number Register 42
- Cylinder Number Registers 42
- Device/Head Register 42
- Status Register 42
- Command Register 43
- HOST SOFTWARE INTERFACE 44
- Control Diagnostic Registers 45
- Reset and Interrupt Handling 46
- SECTION 7 47
- Interface Commands 47
- Read Commands 48
- Read DMA 49
- Read Multiple 49
- Set Multiple Mode 49
- Write Commands 50
- Write Multiple 51
- Write DMA 51
- Set Feature Commands 52
- Power Mode Commands 53
- INTERFACE COMMANDS 54
- Initialization Commands 55
- Initialize Drive Parameters 58
- ERROR CODE DESCRIPTION 59
- 01 No error detected 59
- 00 Master drive failed 59
- 81 Slave drive failed 59
- S.M.A.R.T. Command Set 60
- SECTION 8 61
- Service and Support 61
- Service 62
- Internet 62
- Bulletin Board Service 62
- Customer Service 62
Related products and manuals for Internal hard drives Maxtor 86480D8
(50 pages)© 2020, manymanuals.com. All rights reserved. | 1.268 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals