Maxtor ATLAS 10K III Manual Page 280
- Page / 371
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
SCSI Description
Quantum Atlas 10K II Ultra160/m SCSI Hard Disk Drives 5–213
5.45 VERIFY Command (2Fh)
The VERIFY command verifies the data on the medium for the Logical Block
Address range specified.
Bit
Byte
7 6 5 4 3 2 1 0
0 Operation Code (2Fh)
1 Reserved DPO Reserved BytChk RelAdr
2 - 5 Logical Block Address
6 Reserved
7 - 8 Verification Length
9 Control
Figure 5–105 VERIFY Command Descriptor Block — Data Format
Table 5–99 VERIFY Command — Field Descriptions
Field Description
DPO Disable Page Out. When the value of the field = 1, the device server shall
assign the logical blocks accessed by this command the lowest priority for
being fetched into or retained by the cache.
When DPO = 0, the priority shall be determined by fields in the Caching
page.
BytChk Byte Check. When the value is 1, the drive performs a byte-by-byte
comparison of the data on the medium with the data sent by the initiator
in the data-out buffer transfer.
When 0, the drive performs a medium verification with no data
comparison. In this case, no data is sent by the initiator.
RelAdr Relative Address. This feature is not supported; the field must be 0.
Logical Block Address The address of the first logical sector to be verified.
Verification Length The number of contiguous sectors that are to be verified. The drive returns
a CHECK CONDITION status with the correct sense data if the specified
transfer extends beyond out of the logical sector space.
- Quantum Atlas 1
- 10K II 9.2/18.4/36.7/73.4 GB 1
- Ultra 160/m S 1
- Product Manual 1
- CONTENTS 3
- Chapter 4 SPECIFICATIONS 4
- Chapter 5 SCSI DESCRIPTION 4
- Appendix A QUICK REFERENCE 7
- Contents 10
- Figures (continued) 12
- Tables (continued) 16
- REVISION RECORD 20
- Revision Record 21
- ABOUT THIS MANUAL 22
- 1.4 REFERENCES 24
- About This Manual 25
- GENERAL DESCRIPTION 26
- 2.4 HARDWARE REQUIREMENTS 27
- INSTALLATION 28
- 3.2 SPACE REQUIREMENTS 30
- Shock Feet 31
- 3.3 UNPACKING INSTRUCTIONS 32
- SCSI Connector 33
- Installation 34
- DRIVES WITH 68-PIN SCSI 34
- CONNECTOR 34
- Connector) 38
- Versions 39
- Connector 45
- 3.6.1 Orientation 47
- 160/m SCSI Hard Disk Drive 48
- 3.6.3 Shock Clip 50
- 3.6.4 Mounting 50
- 3.6.5 Ventilation 50
- 3.6.9 Drive Connections 53
- 3.6.9.1 SCSI Bus Connection 53
- 3.6.9.2 Power Connection 53
- 3.6.9.3 Cables 54
- SPECIFICATIONS 56
- Specifications 57
- 4.2 FORMATTED CAPACITY 58
- 4.3 DATA TRANSFER RATES 59
- 4.4 TIMING SPECIFICATIONS 60
- 4.5 POWER 61
- 4.5.1 Power Sequencing 61
- 4.5.2 Power Reset Limits 61
- 4.5.3 Power Requirements 62
- 4.5.3.1 Power Consumption 62
- 4.5.3.2 DC Voltage Tolerances 62
- 4.5.3.3 Current Requirements 63
- Spin-Up Mode 63
- Idle Mode 63
- ECMA Seek Mode 63
- 4.5.3.4 Current Transients 64
- Active Mode (ECMA Seeking) 64
- 4.5.3.6 DC Voltage Monitoring 64
- 4.6 ACOUSTICS 65
- 4.7 MECHANICAL 65
- 4.8 ENVIRONMENTAL CONDITIONS 66
- 4.9 SHOCK AND VIBRATION 66
- 4.10 RELIABILITY 67
- SCSI DESCRIPTION 68
- 5.2 Command Descriptor Block 72
- 5.3 Status/Error Reporting 76
- Table 5–4 Status Codes 77
- Condition 78
- 5.6 Linked Commands 82
- 5.8 SCSI COMMAND DESCRIPTIONS 88
- Common Fields 88
- Index Format 97
- 5.11 INQUIRY Command (12h) 100
- SCSI Description 101
- INQUIRY command if EVPD = 0 102
- 5.13 LOG SENSE Command (4Dh) 120
- 5.13.2 LOG SENSE Log Pages 123
- 5.14.2 Mode Page Types 128
- 5.14.3 Mode Parameter List 128
- 5.14.3.6 Caching Page (08h) 140
- (continued) 155
- 5.16.1 Read-Only Mode Pages 171
- Descriptions (continued) 185
- Persistent 189
- Reservation 189
- Attempted 189
- 5.20 READ (6) Command (08h) 202
- 5.21 READ (10) Command (28h) 204
- 7 6 5 4 3 2 1 0 209
- 4 - 7 Block Length in Bytes 209
- 5.26 READ LONG Command (3Eh) 218
- Descriptions 225
- 5.34.2 Clearing Sense Data 239
- 5.34.3 Status Reporting 239
- SKSV = 1 256
- 5.38 SEEK (6) Command (0Bh) 266
- 5.39 SEEK (10) Command (2Bh) 268
- 5.45 VERIFY Command (2Fh) 280
- 5.46 WRITE (6) Command (0Ah) 282
- FEATURE DESCRIPTIONS 302
- 6.2 PREFETCH 303
- 6.3 WRITE-BACK CACHING 303
- 6.4 ZERO LATENCY READ/WRITE 304
- 6.5 DISCONNECT-RECONNECT 304
- 6.7 AVERAGE ACCESS TIME 304
- 6.8 EMBEDDED SERVO SYSTEM 305
- 6.9.1 Media Error Protection 305
- 6.9.5 Data Verification 306
- 6.10 TAGGED COMMAND QUEUING 306
- 6.11 COMMAND REORDERING 307
- 6.12 BANDED RECORDING 307
- 6.13 SPECIAL FUNCTIONS 307
- 6.14 POWER MANAGEMENT 307
- require operator 307
- 6.15 DIAGNOSTICS 308
- 6.15.3 Host Diagnostics 309
- 6.15.4 Log Sense 309
- 6.16 ERROR RECOVERY 309
- 6.16.1 Seek Error Recovery 309
- 6.16.2 Data Read Errors 309
- INTERFACE 310
- 6.17.1DIFFSENS 311
- 6.17.5 DOMAIN VALIDATION 313
- System Considerations 314
- Feature Descriptions 315
- Quick Reference 316
- Appendix A. Quick Reference 317
- SCSI REFERENCE INFORMATION 322
- B.2 SCSI-3 Bus Timing 325
- B.3 Signal States 330
- B.4 SCSI Signals 332
- B.5 SCSI Bus Phases 333
- B.5.2 ARBITRATION Phase 334
- B.5.3 SELECTION Phase 335
- B.5.4 RESELECTION Phase 336
- B.5.5.3 Wide Data Transfer 342
- B.6 SCSI Bus Conditions 344
- B.6.2 Reset Condition 345
- B.7 SCSI MESSAGE FORMAT 346
- B.8 SUPPORTED SCSI MESSAGES 349
- Bit 7 6 5 4 3 2 1 0 354
- 1 Queue Tag 354
- Appendix C 364
Related products and manuals for Internal hard drives Maxtor ATLAS 10K III
Internal hard drives Maxtor Atlas 10K V Manual
(253 pages)
(253 pages)
© 2020, manymanuals.com. All rights reserved. | 0.151 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals