Maxtor ATLAS 10K III Manual Page 143
- Page / 371
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
SCSI Description
5–76 Quantum Atlas 10K II Ultra160/m SCSI Hard Disk Drives
MODE SELECT (6) Command (15h) (continued)
5.14.3.7 Control Mode Page (0Ah)
The Control Mode page controls the drive’s command processing and error handling
policies.
Bit
Byte
7 6 5 4 3 2 1 0
0 PS Rsvd Page Code (0Ah)
1 Page Length (0Ah)
2 Reserved GLTSD RLEC
3 Queue Algorithm Modifier Reserved Qerr DQue
4 EECA RAC Reserved RAERP UAAERP EAERP
5 Reserved
6 – 7 Ready AEN Holdoff Period
8 – 9 Busy Timeout Period
10 – 11 Reserved
NOTES: 1. Fully supported and temporary fields are underlined. Unsupported and ignored
fields are not underlined. The PS bit is underlined, meaning it will be set on a
MODE SENSE command, since the page is savable.
2. Bytes 8 to 11 are returned only if the device operating definition is
SCSI-3.
Figure 5–33 Control Mode Page — Data Format
- Quantum Atlas 1
- 10K II 9.2/18.4/36.7/73.4 GB 1
- Ultra 160/m S 1
- Product Manual 1
- CONTENTS 3
- Chapter 4 SPECIFICATIONS 4
- Chapter 5 SCSI DESCRIPTION 4
- Appendix A QUICK REFERENCE 7
- Contents 10
- Figures (continued) 12
- Tables (continued) 16
- REVISION RECORD 20
- Revision Record 21
- ABOUT THIS MANUAL 22
- 1.4 REFERENCES 24
- About This Manual 25
- GENERAL DESCRIPTION 26
- 2.4 HARDWARE REQUIREMENTS 27
- INSTALLATION 28
- 3.2 SPACE REQUIREMENTS 30
- Shock Feet 31
- 3.3 UNPACKING INSTRUCTIONS 32
- SCSI Connector 33
- Installation 34
- DRIVES WITH 68-PIN SCSI 34
- CONNECTOR 34
- Connector) 38
- Versions 39
- Connector 45
- 3.6.1 Orientation 47
- 160/m SCSI Hard Disk Drive 48
- 3.6.3 Shock Clip 50
- 3.6.4 Mounting 50
- 3.6.5 Ventilation 50
- 3.6.9 Drive Connections 53
- 3.6.9.1 SCSI Bus Connection 53
- 3.6.9.2 Power Connection 53
- 3.6.9.3 Cables 54
- SPECIFICATIONS 56
- Specifications 57
- 4.2 FORMATTED CAPACITY 58
- 4.3 DATA TRANSFER RATES 59
- 4.4 TIMING SPECIFICATIONS 60
- 4.5 POWER 61
- 4.5.1 Power Sequencing 61
- 4.5.2 Power Reset Limits 61
- 4.5.3 Power Requirements 62
- 4.5.3.1 Power Consumption 62
- 4.5.3.2 DC Voltage Tolerances 62
- 4.5.3.3 Current Requirements 63
- Spin-Up Mode 63
- Idle Mode 63
- ECMA Seek Mode 63
- 4.5.3.4 Current Transients 64
- Active Mode (ECMA Seeking) 64
- 4.5.3.6 DC Voltage Monitoring 64
- 4.6 ACOUSTICS 65
- 4.7 MECHANICAL 65
- 4.8 ENVIRONMENTAL CONDITIONS 66
- 4.9 SHOCK AND VIBRATION 66
- 4.10 RELIABILITY 67
- SCSI DESCRIPTION 68
- 5.2 Command Descriptor Block 72
- 5.3 Status/Error Reporting 76
- Table 5–4 Status Codes 77
- Condition 78
- 5.6 Linked Commands 82
- 5.8 SCSI COMMAND DESCRIPTIONS 88
- Common Fields 88
- Index Format 97
- 5.11 INQUIRY Command (12h) 100
- SCSI Description 101
- INQUIRY command if EVPD = 0 102
- 5.13 LOG SENSE Command (4Dh) 120
- 5.13.2 LOG SENSE Log Pages 123
- 5.14.2 Mode Page Types 128
- 5.14.3 Mode Parameter List 128
- 5.14.3.6 Caching Page (08h) 140
- (continued) 155
- 5.16.1 Read-Only Mode Pages 171
- Descriptions (continued) 185
- Persistent 189
- Reservation 189
- Attempted 189
- 5.20 READ (6) Command (08h) 202
- 5.21 READ (10) Command (28h) 204
- 7 6 5 4 3 2 1 0 209
- 4 - 7 Block Length in Bytes 209
- 5.26 READ LONG Command (3Eh) 218
- Descriptions 225
- 5.34.2 Clearing Sense Data 239
- 5.34.3 Status Reporting 239
- SKSV = 1 256
- 5.38 SEEK (6) Command (0Bh) 266
- 5.39 SEEK (10) Command (2Bh) 268
- 5.45 VERIFY Command (2Fh) 280
- 5.46 WRITE (6) Command (0Ah) 282
- FEATURE DESCRIPTIONS 302
- 6.2 PREFETCH 303
- 6.3 WRITE-BACK CACHING 303
- 6.4 ZERO LATENCY READ/WRITE 304
- 6.5 DISCONNECT-RECONNECT 304
- 6.7 AVERAGE ACCESS TIME 304
- 6.8 EMBEDDED SERVO SYSTEM 305
- 6.9.1 Media Error Protection 305
- 6.9.5 Data Verification 306
- 6.10 TAGGED COMMAND QUEUING 306
- 6.11 COMMAND REORDERING 307
- 6.12 BANDED RECORDING 307
- 6.13 SPECIAL FUNCTIONS 307
- 6.14 POWER MANAGEMENT 307
- require operator 307
- 6.15 DIAGNOSTICS 308
- 6.15.3 Host Diagnostics 309
- 6.15.4 Log Sense 309
- 6.16 ERROR RECOVERY 309
- 6.16.1 Seek Error Recovery 309
- 6.16.2 Data Read Errors 309
- INTERFACE 310
- 6.17.1DIFFSENS 311
- 6.17.5 DOMAIN VALIDATION 313
- System Considerations 314
- Feature Descriptions 315
- Quick Reference 316
- Appendix A. Quick Reference 317
- SCSI REFERENCE INFORMATION 322
- B.2 SCSI-3 Bus Timing 325
- B.3 Signal States 330
- B.4 SCSI Signals 332
- B.5 SCSI Bus Phases 333
- B.5.2 ARBITRATION Phase 334
- B.5.3 SELECTION Phase 335
- B.5.4 RESELECTION Phase 336
- B.5.5.3 Wide Data Transfer 342
- B.6 SCSI Bus Conditions 344
- B.6.2 Reset Condition 345
- B.7 SCSI MESSAGE FORMAT 346
- B.8 SUPPORTED SCSI MESSAGES 349
- Bit 7 6 5 4 3 2 1 0 354
- 1 Queue Tag 354
- Appendix C 364
Related products and manuals for Internal hard drives Maxtor ATLAS 10K III
Internal hard drives Maxtor Atlas 10K V Manual
(253 pages)
(253 pages)
© 2020, manymanuals.com. All rights reserved. | 0.329 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals