Maxtor 5T010H1 User Manual Page 27
- Page / 64
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
AT INTERFACE DESCRIPTION
5 – 2
Pin Description TablePin Description Table
Pin Description TablePin Description Table
Pin Description Table
PIN NAME PIN I/O SIGNAL NAME SIGNAL DESCRIPTION
RESET - 01 I Host Reset Reset signal from the host system. Active during power up and inactive after.
DD0 17 I/O Host Data Bus 16 bit bi-directional data bus between host and drive. Lower 8 bits used for
register and ECC byte transfers. All 16 bits used for data transfers.
DD1 15 I/O
DD2 13 I/O
DD3 11 I/O
DD4 09 I/O
DD5 07 I/O
DD6 05 I/O
DD7 03 I/O
DD8 04 I/O
DD9 06 I/O
DD 10 08 I/O
DD11 10 I/O
DD 12 12 I/O
DD 13 14 I/O
DD 14 16 I/O
DD 15 18 I/O
DMARQ 21 O DMA Request This signal is used with DMACK for DMA transfers. By asserting this signal, the
drive indicates that data is ready to be transfered to and from the host.
DIOW -
STOP
23 I Host I/O Write Rising edge of Write strobe clocks data from the host data bus to a register on
the drive.
DIOR -
HDMARDY
-
HSTROBE
25 I Host I/O Read Read strobe enables data from a register on the drive onto the host data bus.
DMA ready during UltraDMA data in bursts.
Data strobe during UltraDMA data out bursts.
IORDY
DDMARDY
-
DSTROBE
27 O I/O Channel Ready This signal may be driven low by the drive to insert wait states into host I/O
cycles.
DMA ready during UltraDMA data out bursts.
Data strobe during UltraDMA data in bursts.
CSEL 28 Cable Select Used for Master/Slave selection via cable. Requires special cabling on host
system and installation of Cable Select jumper.
DMACK - 29 I DMA Acknowledge This signal is used with DMARQ for DMA transfers. By asserting this signal, the
host is acknowledging the receipt of data or is indicating that data is available.
INTRQ 31 O Hos t Interrupt
Request
Interrupt to the host asserted when the drive requires attention from the host.
IOCS16 32 Device 16 bit I/O Obsolete
PDIAG - 34 I/O Passed Diagnostic Output by drive when in Slave mode; Input to drive when in Master mode.
DA0 35 I Host Address Bus 3 bit binary address from the host to select a register in the drive.
DA1 33 I
DA2 36 I
CS0 - 37 I Host Chip Select 0 Chip select from the host used to access the Command Block registers in the
drive. This signal is a decode of I/O addres ses 1F0 - 1F 7 hex.
CS1 - 38 I Host Chip Select 1 Chip select from the host used to access the Control registers in the drive. This
signal is a decode of I/O addresses 3F6 - 3F7 hex.
DASP - 39 I/O Drive Active/Drive
1 Present
Time-multiplexed, open collector output which indicates that a drive is active, or
tha t
device 1 is present.
GND 02 N/A Ground Signal ground.
19
22
24
26
30
40
KEY 20 N/A Key Pin used for keying the interface connector.
- 5T020H2, 5T010H1 1
- ContentsContents 4
- Contents 4
- FiguresFigures 8
- IntroductionIntroduction 9
- Introduction 9
- ConventionsConventions 10
- Conventions 10
- SECTION 2 11
- Functional / Interface 12
- Cache Management 13
- Major HDA Components 14
- Figure 2-1 15
- Product Specifications 16
- Physical Dimensions (maximum) 17
- PRODUCT SPECIFICATIONS 18
- Handling and Installation 21
- Unpacking and Inspection 22
- Figure 4 - 2 23
- Figure 4 - 3 23
- INSTALLATION 24
- SECTION 5 26
- Pin Description Table 27
- PIO TimingPIO Timing 28
- PIO Timing 28
- DMA TimingDMA Timing 29
- DMA Timing 29
- Ultra DMA Timing 30
- Figure 5 - 5 31
- Figure 5 - 6 31
- Figure 5 - 7 32
- Figure 5 - 8 32
- Figure 5 - 9 33
- Figure 5 - 10 33
- Figure 5 - 11 34
- Figure 5 - 12 34
- Figure 5 - 13 35
- Host Software Interface 36
- Select LBA Mode 37
- Command Register 38
- SummarySummary 39
- Control Diagnostic Registers 40
- Reset and Interrupt Handling 41
- Interface Commands 42
- Read CommandsRead Commands 43
- Read Commands 43
- INTERFACE COMMANDS 44
- Write CommandsWrite Commands 45
- Write Commands 45
- Mode Set/Check Commands 47
- Power Mode Commands 49
- Default Power-on Condition 50
- Initialization Commands 51
- Initialize Drive Parameters 54
- ERROR CODE DESCRIPTION 55
- 01 No error detected 55
- 00 Master drive failed 55
- 81 Slave drive failed 55
- S.M.A.R.T. Command Set 56
- Service and Support 57
- (Singapore time is GMT +8) 58
- GlossaryGlossary 59
- Glossary 59
- SEEK TIMESEEK TIME 63
Related products and manuals for Internal hard drives Maxtor 5T010H1
Internal hard drives Maxtor ATLAS 10K IV Manual
(250 pages)
(250 pages)
Internal hard drives Maxtor ATLAS 10K III Manual
(371 pages)
(371 pages)
Internal hard drives Maxtor Atlas 10K V Manual
(253 pages)
(253 pages)
© 2020, manymanuals.com. All rights reserved. | 0.220 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals