Maxtor 4320 Specifications download pdf (Page 20)

INSTALLATION

4 – 15

Before You Begin

IMPORTANT – PLEASE READ !

Please read this Installation Sheet completely before installing the Maxtor hard drive. It gives general information for installing a Maxtor hard drive in a

typical computer system. If you don’t understand the installation steps, have a qualified computer technician install the hard drive. DO NOT use any low-level

formatting software on this drive.

Handling Precautions

 



Allow the hard drive to reach room temperature

BEFORE

installing it in your computer system.

쇵 쇵

쇵

Hard drives are sensitive to electrostatic discharge (ESD) damage.

Handle the drive by its sides.

DO NOT

touch the printed circuit board assembly.

ᏜᏜ

Ꮬ

NEVER

drop, jar, or bump the drive.

ᏜᏜ

Ꮬ

DON’T

connect/disconnect any drive cables when the power is on.

Tools for Installation

The following tools are needed to complete the installation of your Maxtor hard drive:

◆ For drive capacities 8.4 GB or less, a DOS 5.0

(or higher) or Windows 95 bootable system

diskette

◆ For drive capacities greater than 8.4 GB,

a Windows 95 bootable system diskette

◆ A small (#2) Phillips head screw driver

◆ Small needle-nose pliers or tweezers

◆ Your computer user’s manual

Capacity Barriers

Due to operating system limitations, DOS cannot access the full capacity of drives larger than 8.4 GB. The Microsoft Windows 95 operating system or

equivalent (full installation), NOT a Windows 95 upgrade from DOS (Windows 3.1 or 3.11), is required to obtain the full capacity of any hard drive larger

than 8.4 GB.

Protecting Your Existing Data

Have you backed up your hard disk?

Periodic backup of important data is always a good idea. Whenever your computer is on, there is the potential for losing data on your hard drive. This is

especially true when running disk utilities or any software that directly manipulates your files. Maxtor recommends that you make a backup copy of the

files on any existing hard drives. If required, this data may then be copied to the Maxtor hard drive after it has been installed in your computer. Refer to your

computer user’s manual for detailed data backup instructions.

Capacity Calculations

Maxtor defines one megabyte as 10

or one million bytes (1,000,000) and one gigabyte as 10

or one billion bytes (1,000,000,000).

FDISK, CHKDSK, Windows, BIOS and hard drive manufacturers may show different capacity values for the hard drive as they use different methods and

numbering systems to calculate hard drive capacities. The two most common numeric representations of the hard drive capacity are presented in the base 10

(decimal) and base 2 (binary) numbering systems.

The formula to calculate the capacity of a drive is:

Cylinders * Heads * Sectors * 512

This is a decimal number representing the total number of bytes (characters) that can be stored on the hard drive. To convert this number to binary megabytes

(MB) or gigabytes (GB), this value must be divided by the decimal value of a binary MB or GB. The decimal equivalent of 1 MB (2

) is 1,048,576 and 1 GB (2

) is

1,073,741,824.

Example for a 3.5 GB hard drive:

6,800 * 16 * 63 * 512 = 3,509,452,800 bytes or 3.5 GB using 10

or decimal values.

The equivalent in binary MB is 3,509,452,800 / 1,048,576 = 3,346 MB.

The equivalent in binary GB is 3,509,452,800 / 1,073,741,824 = 3,268 GB.

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 26 27 28

Comments to this Manuals

No comments

Maxtor 4320 Specifications Page 20

Comments to this Manuals